osmo-tetra-sq5bpf

osmocom-tetra from git://git.osmocom.org/osmo-tetra.git , with some patches to decode SDS, and send the results to telive for display and live listening

This is a modified version of osmo-tetra (original README contents are a few lines below).

This version is patched to work with telive - a program for live listening of tetra traffic and recording it, displaying network data etc.

The most important changes are: - support parsing of SDS messages (text messages similar to SMS), including some location protocols - support parsing of D-SETUP, D-RELEASE, D-NWRK-BROADCAST - sending of data and voice traffic via UDP (for consumption with telive or some other program) - incorporate float_to_bits into tetra-rx - implement a crude AFC into tetra-rx and float_to_bits (enables the signal to be less precisely tuned)

For more info about osmo-tetra-sq5bpf and telive:

Main docs (read this first!): https://github.com/sq5bpf/telive/raw/master/telive_doc.pdf Telive repository: https://github.com/sq5bpf/telive Modified osmo-tetra: https://github.com/sq5bpf/osmo-tetra-sq5bpf Script to automatically download/compile/install the acelp codec: https://github.com/sq5bpf/install-tetra-codec Forum thread: http://forums.radioreference.com/voice-control-channel-decoding-software/302347-tetra-decoding.html Tutorial: http://www.rtl-sdr.com/rtl-sdr-tutorial-listening-tetra-radio-channels/

What follows is the original content of the README file:

TETRA MAC/PHY layer experimentation code

© 2010-2011 by Harald Welte [email protected]

This code aims to implement the sending and receiving part of the TETRA MAC/PHY layer.

If you read the ETSI EN 300 392-2 (TETRA V+D Air Interface), you will find this code implementing the parts between the MAC-blocks (called type-1 bits) and the bits that go to the DQPSK-modulator (type-5 bits).

It is most useful to look at Figure 8.5, 8.6, 9.3 and 19.12 in conjunction with this program.

You will need libosmocore (http://bb.osmocom.org/trac/wiki/libosmocore) to link.

== Demodulator ==

src/demod/python/cpsk.py * contains a gnuradio based pi4/DQPSK demodulator, courtesy of KA1RBI src/demod/python/tetra-demod.py * call demodulator on a ‘cfile’ containing complex baseband samples src/demod/python/usrp1-tetra_demod.py * use demodulator in realtime with a USRP1 SDR src/demod/python/usrp2-tetra_demod.py * use demodulator in realtime with a USRP2 SDR

The output of the demodulator is a file containing one float value for each symbol, containing the phase shift (in units of pi/4) relative to the previous symbol.

You can use the “float_to_bits” program to convert the float values to unpacked bits, i.e. 1-bit-per-byte

== PHY/MAC layer ==

=== library code ===

Specifically, it implements: lower_mac/crc_simple.[ch] * CRC16-CCITT (currently defunct/broken as we need it for non-octet-aligned bitfields) lower_mac/tetra_conv_enc.[ch] * 16-state Rate-Compatible Punctured Convolutional (RCPC) coder lower_mac/tetra_interleave.[ch] * Block interleaving (over a single block only) lower_mac/tetra_rm3014.[ch] * (30, 14) Reed-Muller code for the ACCH (broadcast block of each downlink burst) lower_mac/tetra_scramb.[ch] * Scrambling lower_mac/viterbi*.[ch] * Convolutional decoder for signalling and voice channels phy/tetra_burst.[ch] * Routines to encode continuous normal and sync bursts phy/tetra_burst_sync.[ch]

=== Receiver Program ===

The main receiver program ‘tetra-rx’ expects an input file containing a stream of unpacked bits, i.e. 1-bit-per-byte.

=== Transmitter Program ===

The main program conv_enc_test.c generates a single continuous downlinc sync burst (SB), contining: * a SYNC-PDU as block 1 * a ACCESS-ASSIGN PDU as broadcast block * a SYSINFO-PDU as block 2

Scrambling is set to 0 (no scrambling) for all elements of the burst.

It does not actually modulate and/or transmit yet.

== Quick example ==

# assuming you have generated a file samples.cfile at a sample rate of
# 195.312kHz (100MHz/512 == USRP2 at decimation 512)
src/demod/python/tetra-demod.py -i /tmp/samples.cfile -o /tmp/out.float -s 195312 -c 0
src/float_to_bits /tmp/out.float /tmp/out.bits
src/tetra-rx /tmp/out.bits

Related Repositories

osmo-tetra-sq5bpf

osmo-tetra-sq5bpf

osmocom-tetra from git://git.osmocom.org/osmo-tetra.git , with some patches to decode SDS, and send the results to telive for display and live listening ...


Top Contributors

laf0rge sq5bpf smunaut aeburriel blackbit42 oe1rfc Frankas ShinjiLE steve-m